FreeBSD 10.3에서 Seagate USB 3.0 하드 드라이브가 올바르게 인식되지 않는 문제를 해결하는 방법은 무엇입니까?

FreeBSD 버전 : 10.3 Seagate 드라이브 모델 : SRD00F1 USB 3.0 어댑터 : Insignia USB 3.0 PCIe 호스트 카드 (NS-PCCUP53)

드라이브가 이미 연결된 상태에서 재부팅하면 보이지 않습니다. 그러나 드라이브를 연결하면 dmesg.today에서 다음을 볼 수 있습니다.

ugen5.2: at usbus5
umass0: on usbus5
umass0: SCSI over Bulk-Only; quirks = 0x0100
umass0:5:0:-1: Attached to scbus5
da0 at umass-sim0 bus 0 scbus5 target 0 lun 0
da0: Fixed Direct Access SPC-4 SCSI device
da0: Serial Number NA7WF86H
da0: 40.000MB/s transfers
da0: 953869MB (1953525167 512 byte sectors)
da0: quirks=0x2
ugen5.2: at usbus5 (disconnected)
umass0: at uhub5, port 2, addr 2 (disconnected)
da0 at umass-sim0 bus 0 scbus5 target 0 lun 0
da0: s/n NA7WF86H detached
(da0:umass-sim0:0:0:0): Periph destroyed
usb_alloc_device: set address 2 failed (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_IOERROR
ugen0.2: at usbus0 (disconnected)
uhub_reattach_port: could not allocate new device
usbd_req_re_enumerate: addr=1, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 1 failed, USB_ERR_IOERROR
usb_alloc_device: Failure selecting configuration index 0:USB_ERR_TIMEOUT, port 2, addr 1 (ignored)
ugen0.2: at usbus0
ugen0.2: at usbus0 (disconnected)
usbd_req_re_enumerate: addr=1, set address failed! (USB_ERR_IOERROR, ignored)
usbd_setup_device_desc: getting device descriptor at addr 1 failed, USB_ERR_IOERROR
usb_alloc_device: Failure selecting configuration index 0:USB_ERR_TIMEOUT, port 2, addr 1 (ignored)
ugen0.2: at usbus0
ugen0.2: at usbus0 (disconnected)
usb_alloc_device: Failure selecting configuration index 0:USB_ERR_TIMEOUT, port 2, addr 1 (ignored)
ugen0.2: at usbus0

어떤 도움이라도 대단히 감사하겠습니다!

PCIe 슬롯을 변경 한 다음 USB 3.0 카드를 동일한 모델로 교체해도 도움이되지 않았습니다. 그런 다음 온보드 USB (2.0)를 비활성화하려고 시도하여 문제가 해결되었습니다. FreeBSD에서 USB 2.0 및 USB 3.0과 충돌이있는 것 같습니다.