저는 Cisco 무선 네트워킹을 처음 접했고 AIRCAP 3602i 액세스 포인트를 2504 무선 컨트롤러에 연결하려고합니다.
관리 IP 192.168.2.1/24로 무선 컨트롤러를 구성하여 시작했습니다. 이 장치는 다른 것에 연결되어 있지 않습니다 (인터넷 연결에 대한 업 링크조차도).
그런 다음 AP를 무선 컨트롤러에 연결 한 다음 콘솔 케이블을 통해 AP에 연결했지만 아래 오류가 계속 발생합니다.
> Cisco IOS Software, C3600 Software (AP3G2-K9W8-M), Version 15.2(2)JB2,
> RELEASE SOFTWARE (fc1) Technical Support:
> http://www.cisco.com/techsupport Copyright (c) 1986-2013 by Cisco
> Systems, Inc. Compiled Mon 29-Jul-13 11:27 by prod_rel_team
> *Mar 1 00:00:26.379: %SNMP-5-COLDSTART: SNMP agent on host APf872.eae8.67ea is undergoing a cold start
> *Mar 1 00:00:26.399: %CDP_PD-4-POWER_OK: Full power - HIGH_POWER inline power source
> *Mar 1 00:00:26.435: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
> *Mar 1 00:00:27.007: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
> *Mar 1 00:00:27.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
> *Mar 1 00:00:27.435: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
> *Mar 1 00:00:27.499: %DOT11-6-FREQ_SCAN: Interface Dot11Radio0, Scanning frequencies for 9 seconds
> *Mar 1 00:00:27.511: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
> *Mar 1 00:00:28.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
> *Mar 1 00:00:29.855: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed
> *Mar 1 00:00:29.855: DPAA Initialization Complete
> *Mar 1 00:00:29.855: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
>
> *Mar 1 00:00:35.443: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
> *Mar 1 00:00:35.443: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
> *Mar 1 00:00:35.467: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
>
> *Mar 1 00:00:35.599: %SSH-5-ENABLED: SSH 2.0 has been enabled
> *Mar 1 00:00:35.599: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
> *Mar 1 00:00:36.503: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
> *Mar 1 00:00:37.495: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
> *Mar 1 00:00:37.523: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
> *Mar 1 00:00:37.531: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
> *Mar 1 00:00:37.539: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
> *Mar 1 00:00:38.523: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
> *Mar 1 00:00:38.531: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
> *Mar 1 00:00:38.559: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
> *Mar 1 00:00:39.559: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up%Default route without gateway, if not
> a point-to-point interface, may impact performance
> *Mar 1 00:00:55.295: Logging LWAPP message to 255.255.255.255.
>
> *Mar 1 00:00:57.283: %LINK-6-UPDOWN: Interface BVI1, changed state to down
> *Mar 1 00:00:58.283: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
이후 단계에서 위의 오류와 아래의 오류와 유사한 오류가 나타납니다.
Not sending discovery request AP does not have an Ip !!
이 기기를 초기화하는 방법에 대한 표시가 없습니다. AP를 무선 컨트롤러에 연결하면 컨트롤러가이를 감지하지 못합니다.
누군가 AP를 무선 컨트롤러에 연결하는 방법이나 공장 기본값으로 재설정하는 방법에 대해 안내해 줄 수 있습니까?